150-S16138 12 Inch Steering Tube for Jetovator.
|
|
150-B-06592 Berkeley 12JC & 12JG Reverse Control Connector Kit
This kit is for hooking up your forward reverse cable with
all the correct parts from Berkeley Jet
This kit includes:
- 2 Adjusting Nut #S15413
- 1 Retaining Clip #S16609
- 2 Nyliner Bearing #S15414
- 1 Reverse Arm Pin #S15412
Supersedes: 152-K0592
|
|
150-B-06224E This kit includes all of the needed gaskets and O-rings to bring your jet drive back from the dead.
This kit includes:
|
|
150-M-06493 Rudder for the 12JF jet pump. Only works with 12JF pumps.
|
|
150-B-06224 This kit includes all of the needed gaskets and O-rings to bring your jet drive back from the dead.
This kit includes:
|
|
|
|
|
This Part has options, please click the button below to order.
MULTIPLE PART NUMBER OPTIONS. CLICK PART OPTIONS FOR MORE INFO -> 12JI Pump w/Hydraulic Place Diverter, Transom Assembly Not Included
This pump is the latest
evolution of the family of Berkeley Jets With over a million pumps sold
we've used our knowledge to develop the All New Berkeley 12JI Pump.
This pump begins its construction with a super
tough, high strength aluminum alloy 356T alloy casting the strongest most
serviceable aerospace material around Then each unit is CNC machined,
hard anodized, and powder coated "Berkeley White™".
Each unit is assembled using only the
finest in stainless steel hardware, but its what's inside that counts.
Starting with Berkeley's unique single stage mixed flow impeller that
produces maximum thrust per horsepower. The 12JI Pump also incorporates a
special trimming device allowing you to adjust your boat's attitude while
underway through the use of a manual control. A hydraulic control is
optional.
The 12JI Pump is sold as a pump only for
replacement of inferior copy pumps or just a tired original Berkeley unit.
|
|
150-B07336JI 12JI Pump w/Hydraulic Place Diverter, Transom Assembly Not Included (With Exchange)
This pump is the latest
evolution of the family of Berkeley Jets With over a million pumps sold
we've used our knowledge to develop the All New Berkeley 12JI Pump.
This pump begins its construction with a super
tough, high strength aluminum alloy 356T alloy casting the strongest most
serviceable aerospace material around Then each unit is CNC machined,
hard anodized, and powder coated "Berkeley White™".
Each unit is assembled using only the
finest in stainless steel hardware, but its what's inside that counts.
Starting with Berkeley's unique single stage mixed flow impeller that
produces maximum thrust per horsepower. The 12JI Pump also incorporates a
special trimming device allowing you to adjust your boat's attitude while
underway through the use of a manual control. A hydraulic control is
optional.
The 12JI Pump is sold as a pump only for
replacement of inferior copy pumps or just a tired original Berkeley unit.
You can now take advantage of the factory
to consumer special allowing you to trade in your old pump for credit
towards the All New Berkeley 12JI.
|
|
150-S16139 15 Inch Steering Tube
|
|
|
|
|
150-S19212 Extra Long Tiller Pin For Use Of The Billet Tiller Arm
4" Long
|
|
150-L-02507 A Cut Aluminum Impeller
Supersedes: 152-IMB08A
|
|
150-L-05021 A Cut Impeller Stainless Steel
Berkeley Jet's stainless steel XB impeller is a fresh new design from the company that made jet drives famous. Produced using a lost wax precision casting method from high strength 17-4 stainless steel. Featuring a improved center entry cone from the shaft to the blades to reduce cavitation. This CNC machined impeller is factory balanced and has a wear ring surfaced machined at 7.225” to match a factory sized wear ring. Available in standard A and A2 cuts with other cuts available at additional cost.
|
|
150-B06231 All Berkeley pumps seals only kit
|
|
150-1065 Aluminum Impeller, Inducer & Shaft Kit
This do-it-yourself kit comes with a new Berkeley 17-4 stainless steel
machined shaft with the aluminum impeller, inducer, shaft sleeve, thrust
bearing and snap ring pre-mounted.
Choose Impeller Size Below
This kit includes:
|
|
150-B-06906 Aluminum Rudder
If you're looking for some more low-speed maneuverability or improved high-speed tracking then here's your answer Berkeley manufactures two models of bolt-on rudders The first is an entry level economy plastic rudder, while the second is a sturdy cast aluminum version of the same rudder. Note: The plastic unit will not survive in aggressive boating situations If you want durability then you need an aluminum rudder. Rudders sold complete with pin and hardware. NOTE: These only fit stock Berkeley Nozzles, they do not fit any aftermarket trimmable nozzles.
Supersedes: 152-J0595, 152-RK0595
|
|
150-B-05811 Berkeley 12JC and 12JG Intake Bolt Kit
This Berkeley 12JC and 12JG Intake Bolt Kit is comprised of all new stainless
hardware to install your intake assembly.
Includes:
- (16) 1/4" Flat Head Bolts (14 are 2" long and 2 are 2-1/2" long)
- (16) 1/4" Flat Washers
- (16) 1/4" Nuts
- (14) 5/16" Hex Bolts
- (14) 5/16" Lock Washers
|
|
150-100 This Kit Includes:
1-150-L02507, Aluminum Impeller, size A only.
1-150-S10126, Stainless shouldered wear ring.
1-150-S10068, Wear ring insulator.
1-152-K4007, Impeller shim kit.
|
|
150-5000 Jet Drive Water Pressure Relief Kit
The kit from Pack-A-Jet will come with a brass pressure relief valve with 1/2" npt bypass outlet and a stainless steel extension tube for easy installation. Direct fit to the Berkeley models 12JC and 12JG with 3/8" NPT water inlet, but can be used on other models as well as long as they have a 3/8"NPT water inlet on the inside of the boat. Will NOT work on 12JE model or similar pumps where the water inlet is on the outside of the boat. In that case you'll want to buy a pressure relief valve only and a simple T fitting to adapt to the existing inlet tube.
The pressure relief valve opens at app. 12 to 15 psi to move excess water overboard.
Optional hose kits are available see related products below.
|
|
150-4000 Berkeley Jet Stickers 4" Wide x 1-1/2" Tall
|
|
