Pre-Installed Thrust Bearing on Stock Berkeley Impeller Shaft

Here is a factory pump shaft kit from Berkeley Jet Drive.  This kit comes with the thrust bearing pre-greased and installed on the shaft.  This will make your pump rebuild go easier since most boaters do not have a press in their garage.

This kit includes:

• (1) 150-M05356 Stock Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S09018 Bearing Cap Gasket
• (1) 150-S14478 Snap Ring
• (1) 150-S14380 Suction Piece Seal
• (1) 150-S14475 Bearing Cap Seal
• (1) 150-S09017 Bowl Gasket
• Labor to install the sleeve and bearing

Inducer Shaft & Bearing Kit

This kit fits: the standard Berkeley, Most Dominator, and most American turbine pumps.

This kit does not fit Dominator or American Turbine pumps that use the thin thrust bearing. Call for details.

This do-it-yourself kit comes with a new Berkeley 17-4 stainless steel machined shaft with the inducer, shaft sleeve, thrust bearing and snap ring pre-mounted.

This kit includes:

• (1) 150-M05356M Inducer Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S14478 Snap Ring
• (1) 151-1025 Inducer Cavitation Reducer
• Labor to install the sleeve and bearing

Stainless Impeller, Inducer & Shaft Kit

This do-it-yourself kit comes with a new Berkeley 17-4 stainless steel machined shaft with the stainless steel impeller, inducer, shaft sleeve, thrust bearing and snap ring pre-mounted.

This kit includes:

• (1) 150-M05356M Inducer Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S14478 Snap Ring
• (1) 151-1025 Inducer Cavitation Reducer
• (1) 150-S12005 Impeller Nut
• (1) 150-S14482 Impeller Key
• (1) Choice of Berkeley Impeller
• Labor to install the sleeve and bearing

Aluminum Impeller, Inducer & Shaft Kit

This do-it-yourself kit comes with a new Berkeley 17-4 stainless steel machined shaft with the aluminum impeller, inducer, shaft sleeve, thrust bearing and snap ring pre-mounted.

Choose Impeller Size Below

This kit includes:

• (1) 150-M05356M Inducer Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S14478 Snap Ring
• (1) 151-1025 Inducer Cavitation Reducer
• (1) 150-S12005 Impeller Nut
• (1) 150-S14482 Impeller Key
• (1) Choice of Berkeley Impeller
• Labor to install the sleeve and bearing

Berkeley Inducer Impeller Shaft Only, Machined To Accept Cavitation Reducer

This is a stock Berkeley 17-4 stainless steel shaft that has been machined for an inducer.

Pump Shaft With Bearing

Here is a factory pump shaft and bearing from Berkeley Jet Drive.  This kit comes with the thrust bearing pre-greased and installed on the shaft.  This will make your pump rebuild go easier since most boaters do not have a press in their garage.

This kit includes:

• (1) 150-M05356 Stock Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S14478 Snap Ring
• Labor to install the sleeve and bearing

Inducer Shaft W/ Bearing

This kit fits: the standard Berkeley, Dominator, and American turbine pumps.

This do-it-yourself kit comes with a new Berkeley 17-4 stainless steel machined shaft with the shaft sleeve, thrust bearing and snap ring pre-mounted.

This kit includes:

• (1) 150-M05356M Inducer Impeller Shaft
• (1) 150-S14379 Shaft Sleeve
• (1) 150-S14063 Thrust Bearing
• (1) 150-S14478 Snap Ring
• Labor to install the sleeve and bearing

Brass 43C Cable Attaching Pivot, 1/4" Shaft, 3/8" Shaft Length, 1/4-28 thread

This brass pivot is designed to thread onto your 43C jet boat shift control. Uses a 1/16" cotter pin. (Not Included)